Alexor PC9155G-868 Guía de instalación descargar pdf (Pagina 61)

5.3 Programming Descriptions

5-42

[804][141]-[156] Wireless Key Function Key Options

Up to 6 unique functions can be programmed for each wireless key. Each section requires four 2-digit entries. The following table describes each programmable function.

[804][181]-[182] Wireless Key Enable/Disable

These sections enable each individual key enrolled on the system. The keys are all enabled on the system by default.

[804][201]-[204] Wireless Keypad Serial Number

These sections are used to enter the wireless keypad serial numbers. The number is an 8-digit hexadecimal entry. To toggle between decimal and hexadecimal value

entries, press [

].

[804][301]-[304] Wireless Siren Serial Number

These sections are used to enter the wireless siren serial numbers. The number is an 8-digit hexadecimal entry. To toggle between decimal and hexadecimal value

entries, press [

].

[804][311]-[314] Wireless Siren Options for Sirens 1-4

Entry Description DSC Wireless Key

Null Key (Key Not Used) YES

Stay Arm YES

Away Ar m YE S

[][9] No-Entry Arm [][9] No-Entry Arm can be used if the wireless key being used is identified.

[][4] Chime On / Off YES

Command Output 1 [][7][1] [][7][1] commands can be used with an access code if the wireless keys are identified.

Command Output 2 [][7][2] [][7][2] commands can be used with an access code if the wireless keys are identified.

[][0] Quick Exit YES

[][1] Reactivate Stay/Away Zones YES

Instant Stay Arm YES

Disarm (Off) Disarming can be used with an access code, as long as the wireless keys are identified.

Auxiliary Alarm YES

Panic Alarm YES

Night Arm YES

Each section contains the following 8 options:

Option Description

[1]

ON: Siren Enabled. The WT49X1 shall activate at full volume for fire, burglary, and CO alarm conditions. This option shall also enable walk test

and system test indications for WT49X1 modules, and placement test, walk test, and system test indications for WT4911 modules.

OFF: Siren Disabled. The WT49X1 will not activate for fire, burglary, CO Alarm, walk test or system test indications. Placement test will still be

sounded by WT4901 modules.

[2]

ON: Buzzer Notifications Enabled. The siren will activate audible signals for entry/exit delays, and 24 hour buzzer zone alarms. This may be desir-

able for indoor sirens, but not outdoor sirens.

OFF: Buzzer Notifications Disabled. Audible signals will not be sent.

[3]

ON: Door Chime Enabled. The siren will activate for door chime conditions.

OFF: Door Chime Disabled. The siren will not be activated for door chime conditions.

[4]

ON: Trouble Beeps Enabled. The siren will activate for trouble beep conditions. Trouble beeps are sounded until any key on the keypad is pressed or

until all trouble conditions are restored. This is intended for indoor sirens, but not outdoor sirens or sirens that are mounted in a sleeping area.

Off: Trouble Beeps Disabled. The siren will not activate for trouble beeps.

[5]

ON: Bell Squawks Enabled. The siren will activate programmed bell squawk conditions (e.g., arming, disarming, disarming with alarms in mem-

ory). This may be desirable for outdoor sirens, but not indoor sirens. These squawks are sounded at full alarm volume.

OFF: Bell Squawks Disabled. The siren will not activate for bell squawk conditions.

[6]

ON: Strobe Enabled. The strobe will activate for alarms, placement test, walk test, system test and arm/disarm squawk indications. The strobe can be

used to identify a system alarm before entering the premises.

OFF: Strobe Disabled. The strobe will not be activated.

[7]

ON: Buzzer Alarm / Strobe Follows Bell Time Out. Indoor Siren - If the indoor siren is set for buzzer notifications (option 2), buzzer alarms, such

as 24 Hr buzzer zone types are shut off after they have been active for the duration of BTO. Outdoor siren: If the strobe is enabled on the outdoor siren

(option 6), the strobe will shut off once the siren is shut off at the end of the bell duration.

OFF: Buzzer Alarms / Strobe Follows Alarm Condition. Indoor siren - The siren will sound the buzzer alarm until the alarm condition has been

acknowledged (silenced) at the keypad. Outdoor siren: The strobe will continue until an access code has been entered at a system keypad, or a suc-

cessful disarming request has been serviced.

[8]

ON: Siren Tamper Enabled. Tamper conditions from the siren will generate a tamper trouble. The panel will log and communicate the event.

OFF: Siren Tamper Disabled. Tamper conditions from the siren will not generate a tamper trouble. The panel will log and communicate the event.

If a siren tamper condition is present in [

✱ ][2], turning off this option shall clear the trouble from the system.

This option must be Off for CP-01 compliance.

1 2 ... 56 57 58 59 60 61 62 63 64 65 66 ... 79 80

Comentarios a estos manuales

Sin comentarios

Alexor PC9155G-868 Guía de instalación Pagina 61

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Alexor PC9155G-868