Alexor PC9155G-868 Guía de instalación

Models: PC9155-433/868 PC9155G-433/868 PC9155D-433/868 PC9155I-433/868Used with: WT5500-433/868 WT5500P-433/868 Series 2-way Wireless Keyp

PC9155 Wireless Alarm System2-32.2 Wiring1 I/O WiringThe two I/O terminals can be programmed as hard-wired zone inputs and/or PGM outputs. See program

2 Installation2-42.3 Wireless Device EnrollmentInstalling a wireless device requires programming the system with the Electronic Serial Number (ESN) of

PC9155 Wireless Alarm System2-5Enrolling Additional Keypads, Sirens & Wireless Keys1. Enter [ ✱ ][8][5555][898]. The following is displayed: “Wire

2 Installation2-6To perform a global placement test on a zone, type [00]. In this mode, all wireless zones, keypads and sirens are placement tested at

PC9155 Wireless Alarm System3-13 Operation3.1 Operating Modes3.1.1 – Away ArmingAway Arming arms the entire system including the perimeter and interio

3 Operation3-2Re-activate Stay/Away and Night Zones:Press [ ✱ ][1] when the system is armed in the Stay mode to change the armed status to Away mode o

PC9155 Wireless Alarm System3-3[ ✱ ][6] – User FunctionsTo access the User Functions section, press [ ✱ ][6] followed by the master or supervisor code

4 Programming4-14 ProgrammingThe PC9155 can be programmed using the following methods:4.1 Template ProgrammingTemplate Programming allows the installe

PC9155 Wireless Alarm System4-2• Digit 1 selects one of the following zone definition options for the first 8 zones. A “0” in the digit 1 location ind

4 Programming4-3Digit 4 indicates/selects one of the following DLS connections:4.2 DLS Programming4.2.1 Local Programming with PC-LinkFollow the steps

i SAFETY INSTRUCTIONS FOR SERVICE PERSONNELWARNING: When using equipment connected to the telephone network, there are basic safety instructions that

PC9155 Wireless Alarm System5-15 Installer Programming5.1 Index to Programming OptionsSect Description

5 Installer Programming5-25.2 Programming WorksheetsNACPEU00 Null Zone 14 24 Hour Heat 28 Future Use01 Delay 1 15 24-Hour Medical 29 Future Use02 Dela

PC9155 Wireless Alarm System5-300 Null PGM (Not Used) TLM and Alarm01 Fire and Burglary Output For Future Use02 For Future UseAway Armed Status03 For

5 Installer Programming5-4NA CP EUON OFF1 Cross Zoning is Enabled  Police Code is Enabled29 Exit Delay Restart Enabled  Exit Delay Restart Disable

PC9155 Wireless Alarm System5-5Zone TypeiFor CP-01 installations: Option 6 (Swinger) is defaulted ON for zone definitions 09-11, 13-17, 19, 20.

5 Installer Programming5-6NA CP EU NA CP EU[202] Zone 1-8 [203] Zone 9-16 [204] Zone 17-24 [205] Zone 25-32 [206] Zone 33-34NA CP EU NA CP EU NA CP EU

PC9155 Wireless Alarm System5-7Keypad [A]uxiliary RestoreKeypad [P]anic RestoreFor Future UseKeypad [P]anic AlarmFail to Report InKeypad [F]ire Restor

5 Installer Programming5-8Partial ClosingSpecial ClosingExit Fault[341] Miscellaneous Closing (Arming) Reporting CodesClosing By Access Code 40Automat

PC9155 Wireless Alarm System5-9000000000000Phone #4 FTC RestoreInstaller Lead InPhone #3 FTC RestoreGeneral Zone Low Battery RestoreInstaller Lead Out

5 Installer Programming5-10[350] Communicator Format Options1st Telephone Number 2nd Telephone Number 3rd Telephone Number 4th Telephone NumberCP01 20

iiKuva 1MakuuhuoneMakuuhuoneMakuuhuoneOlohuoneKeittiöGuidelines for Locating Smoke & CO DetectorsThe following information is for general guidance

PC9155 Wireless Alarm System5-11NA CP EUON OFF1999 Communications Enabled  Communications Disabled2 Restores On Siren Time-Out  Restores Follow Zo

5 Installer Programming5-12NA CP EUON OFF1Answering Machine / Double Call Enabled Answering Machine / Double Call Disabled2999 User Enable DLS  Us

PC9155 Wireless Alarm System5-13*Attributes for Option 9 & 10 SectStart Time End TimeValid times areNA CP EUON OFF1 Tampers Enabled  Tampers Dis

5 Installer Programming5-14NA CP EUON OFF19 50 Hz AC Input  60 Hz AC Input2 Time Base is Internal Crystal  Time Base is AC Line3AC/DC Arming Inhi

PC9155 Wireless Alarm System5-15Sect.Value = Entry x 15 minutes. E.g., 6 x 15 minutes equals 1.5 hrs. Valid entries are 4-96 (1Hr - 24Hr)[082] [083]

5 Installer Programming5-16Enable/Disable#5Def03Def04Def27Def30Def13Def14DefRefer to section [804][141]-[156] in the Programming Descriptions section

PC9155 Wireless Alarm System5-17NA CP EUON OFF1999 Siren Alarm Enabled  Siren Alarm Disabled299 Buzzer Notifications Enabled  Buzzer Notifications

5 Installer Programming5-18 Enter [999][Installer Code][999] See Chapter 6.3 Resetting the System to Factory DefaultsFunction Key Options[00] Null Key

PC9155 Wireless Alarm System5-19—NA CP EUON OFF1999 [F] Key Enabled  [F] Key Disabled2999 [A] Key Enabled  [A] Key Disabled3999 [P] Key Enabled 

5 Installer Programming5-20NA CP EUON OFF1999 Local Clock Display Enabled  Local Clock Display Disabled2 Local Clock Displays 24 Hr Time  Local Cl

iiiLimited WarrantyDigital Security Controls warrants the original purchaser that for a period of twelve months from the date of purchase, the product

PC9155 Wireless Alarm System5-21ASCII ChartiASCII entries 000-007 are special characters that vary based on the language selected.!“#$%&‘ ( ) *+,

5.3 Programming Descriptions5-225.3 Programming DescriptionsThis section describes all of the PC9155 programming options. [001]-[002] Zone Definitions

PC9155 Wireless Alarm System5-23iThis zone type must NOT be used for wireless zones. Activation of a keyswitch zone is intended to arm or disarm the s

5.3 Programming Descriptions5-24[005] System Timers This section has two subsections. Entry/Exit delays are in subsection 01and Bell Cut-off is in sub

PC9155 Wireless Alarm System5-25[012] Keypad Lockout Options This section determines how the keypad lockout function operates. 07Keypad Buzzer Follow.

5.3 Programming Descriptions5-26[013] First System Options [014] Second System Options[015] Third System Options Option Description[1]ON: Zone 33/PG

PC9155 Wireless Alarm System5-27[016] Fourth System Options [3] ON: Quick Exit Enabled. See [][0] in section 3.3 [] Commands.OFF: Quick Exit Disab

5.3 Programming Descriptions5-28[018] Sixth System Options [023] Tenth System Options Code[024] Eleventh System Options Code Option Description[1]Fo

PC9155 Wireless Alarm System5-29[030] Zone Loop Response [101]-[134] Zone Attributes The following options can be enabled or disabled for each zone.

5.3 Programming Descriptions5-30[167] GPRS/Ethernet Interface Communications Wait for ACK[168]-[169] Daylight Saving Time [170] PGM Output Timer[176]

ivTable of ContentsChapter Description Page1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PC9155 Wireless Alarm System5-31 [301] First Telephone Number[302] Second Telephone Number[303] Third Telephone Number[304] Call Waiting Cancel Dialin

5.3 Programming Descriptions5-32[328] Miscellaneous Alarm Reporting CodesDuress AlarmThis reporting code is transmitted whenever a Duress code is used

PC9155 Wireless Alarm System5-33Exit FaultIf an Exit Error occurs and entry delay expires before the system is disarmed, this reporting code is sent.

5.3 Programming Descriptions5-34two ways: after the panel has been successfully called by DLS, but before the panel calls DLS back via the downloading

PC9155 Wireless Alarm System5-35Swinger Shutdown (Tampers & Restores)This value determines the number of times the same system Tamper type event o

5.3 Programming Descriptions5-36[381] Second Communicator Options Code [382] Third Communicator Options Codei If all 5 attempts to the designated phon

PC9155 Wireless Alarm System5-37[383] Fourth Communicator Options Code[389] GPRS/Ethernet Fault Check TimerThe programmed number of poll commands that

5.3 Programming Descriptions5-38[402] Downloading Computer’s Telephone NumberThis phone number enables the control panel to call the downloading compu

PC9155 Wireless Alarm System5-39[591]-[592] Inactivity TimersInactivity timers are used to create two windows to monitor 24-Hour. non-alarm zone activ

5.3 Programming Descriptions5-40[610] Alternate Communicator Receiver Trouble Reporting CodesThis section is used for programming alternate communicat

PC9155 Wireless Alarm System1-11 IntroductionThis manual provides installation and programming information for the PC9155 two-way wireless series of a

PC9155 Wireless Alarm System5-41[800] Door Chime Options for Zones 1-34 [804]-[001]-[032] Wireless Device Serial NumberThese sections are for manual e

5.3 Programming Descriptions5-42[804][141]-[156] Wireless Key Function Key OptionsUp to 6 unique functions can be programmed for each wireless key. Ea

PC9155 Wireless Alarm System5-43[804][320] Global Siren Options [804][330] WT4911 Maximum Bell Activation TimeThis value determines the maximum time t

5.3 Programming Descriptions5-44[] Keypad ProgrammingTo enter Keypad Programming press [][8][Installer Code][]. Keypad sections require 3-digit ent

PC9155 Wireless Alarm System5-45[001]-[069], [100]-[125] Label ProgrammingZone and other labels in these sections can be customized. Default labels ar

5.3 Programming Descriptions5-46[075] Second Keypad Options[076] Third Keypad Options[077] LCD MessageEnter a 32 character message. If anything other

PC9155 Wireless Alarm System5-47[996] Reset Labels to Factory DefaultResets all custom labels to the factory defaults. See this section in the Program

6 Testing & Troubleshooting6-16 Testing & Troubleshooting6.1 Testing the SystemInform the monitoring station when beginning or ending alarm sy

PC9155 Wireless Alarm Panel6-26.3 TroubleshootingGeneral Start-up TroublesTrouble Cause Troubleshooting"Failed to Enroll" message displayed

6 Testing & Troubleshooting6-3Alternate Comm Receiver TroubleThis condition is generated when the GPRS/Ethernet module loses supervision or fails

1 Introduction1-21.3 Controls & IndicatorsThe PC9155 can have a maximum of eight status indicators located on the front panel. The four indicators

PC9155 Wireless Alarm Panel6-46.4 Battery Removal/ReplacementDisconnect AC power and battery before proceeding.Removal: 1. Disconnect battery cable fr

Appendix A: Reporting Code FormatsAPP-1Appendix A: Reporting Code FormatsThe following tables contain Contact ID and Automatic SIA format reporting co

PC9155 Wireless Alarm PanelAPP-2Section #Reporting Code Code Sent W henDialer DirectionAutomatic Contact ID CodesSIA Auto Rep Codes[346]AC Line Restor

Appendix A: Reporting Code FormatsAPP-3Section #Reporting Code Code Sent W henDialer DirectionAutomatic Contact ID CodesSIA Auto Rep Codes[347]Siren 4

PC9155 Wireless Alarm PanelAPP-4Contact ID Programmed Zone Alarm/Restoral Event Codes(as per SIA DCS: “Contact ID” 01-1999):Program any of these codes

Appendix B: Communicator Format OptionsAPP-5Appendix B: Communicator Format OptionsThe following format options are programmable in section [350] 0102

PC9155 Wireless Alarm PanelAPP-6Appendix C: 2-Way Audio Verification (PC5950)Not approved for use with UL/ULC listed installations.Audio Verification

Appendix D: Regulatory Approvals InformationAPP-7 Appendix D: Regulatory Approvals InformationNorth America FCC COMPLIANCE STATEMENTwill provide advan

PC9155 Wireless Alarm PanelAPP-8This product has been tested and found in compliance with the following standards:UL1023 Household Burglar-Alarm Syste

Appendix D: Regulatory Approvals InformationAPP-9SIA False Alarm Reduction InstallationsFor a list of the defaults value programmed when the unit is s

PC9155 Wireless Alarm System2-12 InstallationThis chapter describes how to install the panel and how to configure it to work with associated devices s

EuropeThis product is in conformity with:EMC Directive 2004/108/EC based on results using harmonized standards in accordance with article 10(5), R&

2 Installation2-2 Figure 2-3 Mounting & Wiring Details Phone Line T1-Brn Connects to in-house phone lineR1- Gra Connects to in-house phone lineTip