Alexor PC9155D-433 Guía de instalación descargar pdf (Pagina 87)

Appendix D: Regulatory Approvals Information

APP-9

SIA False Alarm Reduction Installations

For a list of the defaults value programmed when the unit is shipped from the factory and for any other programming information refer to table below.

Caution: Call Waiting Cancel (section [382], Option 4) feature on a non-Call Waiting line will prevent successful communication to the supervising station.

Fire Alarm Verification feature (Auto Verified Fire Zone type [89]) is supported on the DSC Wireless Smoke Detector, Model WS4916. The fire alarm delay is 40s.

Notes: Programming at installation may be subordinate to other UL requirements for the intended application

Cross zones have the ability to individually protect the intended area (e.g., motion detectors which overlap)

Cross zoning is not recommended for line security Installations nor is it to be implemented on exit/entry zones.

This pannel has a communication delay of 30 seconds. The delay can be removed or it can be increased up to 45 seconds at the request of the end user in consultation with the

installer.

Do not duplicate any reporting codes. This applies to all communication formats other than SIA or CID sending automatic programmed reporting codes.

The security system shall be installed with the sounding device activated and the communicator enabled for transmission using SIA or CID format.

SIA Feature

Programming Section

Comments Range/Default Requirement

Exit Time

[005], 3rd entry

Access to entry and exit delays and bell time out for the system

Range:

45- 255 seconds

Default:

60 sec.

Required

(programma-

ble)

Progress Annunciation/

Disable - for Silent Exit

[014], Option 6 ON

Enables audible exit beeps from the keypad for the duration of exit delayKeypads may be disabled

Default:

Enabled

Allowed

Exit Delay Restart Enabled

[016], Option 2 ON

Enables the exit delay restart feature

Default:

Enabled Required

Auto Stay Arm on

Unvacated Premises

[001]-[002] Zone type 05, 06, 32

Function Key: Stay Arming. All Stay/Away type zones (05, 06) and Instant Stay/Away

zones (32) will be automatically bypassed

If no exit after full arm

Default:

Enabled

Required

Exit Time and Progress

Annunciation/Disable

or Remote Arming

[005] and [014] bit 6

System times and audible exit beeps can be disabled when using the wireless key to

Away Arm the system

Default:

Enabled Allowed

Entry delay(s)

[005], 1st and 2nd entry

Access to entry and exit delays and bell time out for the system

Note:

Combined entry delay and communications delay (Abort window) shall not

exceed 60s

Range:

30 sec. to 4 min.

Default:

30 sec.

Required

(programma-

ble)

Abort Window

for Non-Fire zones

[101]-[134] bit 7 ON

Access to zone attributes, i.e., swinger shutdown, transmission delay and cross zone.

Individual zones attribute bit 7 (Transmission delay) is by default ON

May be disabled

by zone or zone type

Default:

Enabled

Required

Abort Window - for

Non-Fire zones

[377], 4th entry

Access to the programmable delay before communicating alarms

Note:

Combined entry delay and communications delay (Abort window) shall not

exceed 60s

Range:

15 - 45 sec.

Default:

30 sec.

Required

(programma-

ble)

Abort Annunciation

[382], Option 3 ON

Enables the “Communication Cancelled” message display on keypadAnnunciate that no

alarm was transmitted

Default:

Enabled

Required

Cancel Annunciation

[328], 8th entry

Access to the reporting code for alarm cancelled Annunciate that a

Cancel was transmitted

Default:

Enabled

Required

Duress Feature

[*][5] Master Code

Option 2 ON

Do not derive code from an existing Master/User code (e.g., Master code is 1234, the

duress code should not be 1233 or 1235)

No 1+/- derivative of another

user code. No duplicates with

other user codes

Default:

disabled

Allowed

Cross Zoning

[016] Option 1

[101]-[134] bit 8 OFF

This option enables cross zoning for the entire system. Individual zones can be

enabled for cross zoning via zone attribute bit 8 in sections [101] - [134]

Programming required

Default:

Disabled

Required

Cross Zone Timer

[176]

Access to the programmable cross zone timer May program

Range: 001-255 sec./min.

Default:

60 seconds

Allowed

Swinger Shutdown for Alarms

[377] 1st entry

Access to the swinger shutdown limit for zone alarms For all non-fire zones

shut down at 1 or 2 trips

Default:

1 Trip

Required

(programma-

ble)

Swinger Shutdown Enable

[101] - [134] bit 6 ON

Access to zone attributes, i.e., swinger shutdown, transmission delay and cross zone.

Individual zones attribute bit 6 (Swinger Shutdown enabled) is by default ON

For non-police

response zones

Default:

Enabled

Allowed

24-Hr. Auto-verified Fire

(Wireless) Zone type [89]

Access to 24-Hr. Auto-verified fire (wireless)Activates If a restoral is Not

received within the specified

time

Default:

disabled

Required

Call Waiting Cancel Dial String

[304], [382], Option 4 OFF

Access to the dialing sequence used to disable call waiting Dependant on user phone

line

Default:

disabled

Required

Testing

System Test:

[*][6] Master Code, Option 4

The system activates all keypad sounders, bells or sirens for 2 seconds and all keypad lights turn on.

Refer to the User Manual (part no. 29007326).

Walk Test Mode:

[*][6] Opt 8

This mode is used to test each zone on the system for proper functionality.

1 2 ... 82 83 84 85 86 87 88

Comentarios a estos manuales

Sin comentarios

Alexor PC9155D-433 Guía de instalación Pagina 87

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Alexor PC9155D-433