Alexor PC9155D-433 Guía de instalación descargar pdf (Pagina 12)

PC9155 Wireless Alarm System

2-4

2.3 Wireless Device Enrollment

Installing a one-way or two-way wireless device requires programming the system with the Electronic Serial Number (ESN) so that it can be

identified when an event is communicated. Two-way devices must also initiate communication with the control panel to complete the enrollment

process. The control panel will then assign the device a unique system ID, device ID and encryption key. This information is sent to the device

and is stored in its memory. The system uses these ID's and encryption to communicate events.

Methods of Enrollment

Two methods of enrollment are available:

• Quick Enroll – Used to enroll new devices on the system. (See below for procedure). The

Quick Enroll

procedure performs two-

way enrolment communications in the background. The Two-way device and One-way device enrollment procedures are identical.

• Manual or DLS Enroll – See Installer Programming or DLS Programming (section [804]). Manual or DLS enrollment of two-way

wireless keys requires the device to be physically triggered to complete the enrollment.

1c. PC5950 2-Way Audio Verification Module Wiring

• Install the PC5950 in a metal cabinet secured to a wall.

• Power down the PC9155 if required.

• Route wiring to the PC9155 through the wiring guide.

• Route wiring to the audio stations as indicated (2 Max).

• Ensure telephone line wiring enables the PC9155 to seize the line.

• Test System. Refer to the PC5950 Installation Guide.

Refer to Appendix D: 2-Way Audio Verification (PC5950).

Program I/O 1 - Audio Verification PGM

Program I/O 2 - Audio Verification Monitor Zone

2. Telephone Line Wiring

Wire the incoming line (phone company) and outgoing line (premises) to the

connection terminals of an RJ31x connector as indicated. This will allow line

seizure if required by the alarm system. Use 24AWG minimum for wiring.

Communication formats are programmed in section [350].

Telephone call directions are programmed in sections [351]-[376].

3. Battery 4. AC Wiring

Sealed Lead Acid Battery

Model FP 1223 ................................. 12V

DC 2.3Ah@20Hr. discharge rate

Standby...............................................................................................24Hr

Battery Replacement

Removal:

(1) Disconnect the RED (+) and BLACK (-) connectors from the battery.

(2) Depress the plastic battery retainer on the right side of the battery with

thumb to free battery from the housing, then remove battery.

Replacement:

(1) Remove terminal protection from battery.

(2) Install battery cable on battery spade lug terminals.

(3) Slide left side of battery [(+) terminal] under the left battery retaining

bracket.

(4) Insert a slot screwdriver between the battery and right retaining bracket.

Lever the right retaining bracket to the right while pressing the battery firmly in

place.

(5) If required route battery cable through wire guides and connect to the battery

connector.

• DSC recommends battery replacement every 3-5 years.

• Dispose of battery in accordance with local regulations.

AC Transformer Requirements:

Primary: 120VAC, 60Hz., 0.200A (For UL/ULC Listed installations)

240VAC, 50Hz., 0.100A

(Fuse: 503 Si, 250V/160mA Fast-Blo)

Secondary: 16.5V

AC/20VA

The following plug-in transformers shall be used:

North America (UL Listed Installations)

PTD1620U-CC

Canada (ULC Listed Installations)

PTD1620

Do NOT connect transformer to a receptacle controlled by a switch. Use a Class 2, power limited transformer for UL/ULC installations.

3&

$8;

,2

,2

<HO

3&

$8;

%ON

%HOO

5HG

%HOO

*UQ

2II

.

$/0

2II

.,662II

,2

,2

<HO

$8;

%ON

%HOO

5HG

%HOO

*UQ

2II

$/0

2II

.,662II

&20

7DON/LVWHQZLWK6LUHQ6KXWGRZQ

/LVWHQLQ2QO\ZLWK6LUHQ6KXWGRZQ

5LQJ

5

7

7LS

)URP

2XWVLGH

3KRQH /LQH

7R +RXVH

3KRQHV

5LQJ

5

7

7LS

3&

3&

5LQJ

5

7

7LS

)URP

2XWVLGH

3KRQH

/LQH

7R +RXVH

3KRQHV

5LQJ

5

7

7LS

PC5950 Programming

Section 01 - Set to 1 (Hard Trip)

Section 10 - Set to 2 (Trigger

Enable:Auto Trip by Bell or Green)

PC5950 Programming

Section 01 - Set to 1 (Hard Trip)

Section 07 - Set to 1 (Trigger High)

Section 10 - Set to 2 (Trigger Enable:

Auto Trip by Bell or Green)

T-1

R-1

TIP

RING

RJ-31X

RED

GRN

BRN

GRA

Internal Transformer

Secondary Wire Run Distance

AWG Feet Meters

5.8

9.3

14.8

23.5

1.8

2.8

4.5

7.2

Wiring diagram 1, Talk/Listen with Siren Shutdown, does a full

talk/listen in session for silent alarms. If a listen in only session is

required for silent alarms, use wiring diagram 2, Listen-in Only

with Siren Shutdown.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 87 88

Comentarios a estos manuales

Sin comentarios

Alexor PC9155D-433 Guía de instalación Pagina 12

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Alexor PC9155D-433